FrSky TFR8SB 7-k FASST-mottagare Med PPM-utgång

420.00 kr

En FASST-mottagare med SB-utgång från FrSky. 7 kanaler – full räckvidd!

15 i lager

Artikelnr: FS-TFR6-SB Kategori:

Produktbeskrivning

Kompabilitet:
FASST 2.4G: Air Systems (7CH Mode/Multi Mode)
FrSky TF Modules: TF-8M, TF-14M
Specifikation:
Antal kanaler: 7
Drivspänning:  3.5V~10V
Dimension: 37*22*8mm
Vikt: 7.8g
 

 

 

 

 

Egenskaper

1) Lättare och mindre än andra mottagare
2) Två valbara FaiSafe-inställningar
Bindningsprocedur
Slå på sändaren. Håll F/S-knappen intryckt på mottagaren och slå på strömmen. När mottagarens röda LED-lampan slocknat och den gröna LED-lampan tänts är bindningen klar.
Programmering av FailSafe
TFR6 stöder två olika sätt att ha FailSafe. Antingen sändarens FailSafeprogrammering eller mottagarens egna programmering.
Sändarens FailSafe
Om sändarens FailSafe är aktiverad kommer mottagaren att använda den programmeringen.
FailSafeprogrammering av mottagaren
TFR6 har FailSafe på alla kanalerna. Följ dessa enkla steg för programmering av mottagarens FailSafe:
1) Bind sändare och mottagare.
2) Inaktivera sändarens FailSafe.
3) Ställ sändarnas kontroller i det läge som önskas vid ett radiobortfall.
4) Tryck kort på mottagarens F/S-knapp. Den gröna LED-lampan kommer att blinka två gånger, vilket indikerar att FailSafe-programmeringen lagrats i mottagaren.  
För att ta bort mottagarens FailSafeprogrammering måste mottagaren bindas om.
TIPS:  Om FailSafeprogrammeringen är aktiv i sändaren kommer mottagaren att använda den programmeringen.
LED status:
RÖD LED GRÖN LED Mode
Off On Normal mode
On On Väntar på att bindas
Blinkande On Ingen Signal
On Blinkar två gånger FailSafe lagrat

 

 

1.  Introduction

   1.1.1  Compatible systems

   FASST 2.4GHz Air Systems (7CH Mode/Multi Mode): 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc.

   1.1.2  Compatible servos at SB port

   Futaba S.BUS servos, FrSky S Bus compatible servos D12MB

   Model: TFR8SB (8CH FASST compatible receiver with RSSI & SB ports)

   Dimension: 44.5*27.5*17mm

   Weight11.5g

   Operating Voltage Range: 3.5~10V

   Operating Temperature Range: -10℃~80℃

   Servo Frame Rate: 14ms (FS – Normal Speed Mode)

                                        7ms (HS – High Speed Mode)

Note: Be sure that when using battery or regulated output from ESC, the capacity must meet the usage conditions of servos.

  1.3 Features

     1) Compatible with FASST 2.4GHz Air Systems (7CH Mode/Multi Mode)

     2) SB port is compatible with Futaba S.BUS servos and FrSky S Bus compatible servos

     3) With RSSI output

     4) Two selectable failsafe setting options (use native failsafe on radio side or set failsafe on TFR8SB side)

     5)S.BUS servos/S Bus compatible servos channel setting channel setting on TFR8SB

     6)Improve sensitivity and stability

     7)Wider and higher operating temperature range, suitable for all kinds of models

     8)Firmware upgradeable

2.  Set Up

   2.1 Bind procedure

   Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is

off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.

   2.2 Setting failsafe

   TFR8SB support two selectable failsafe setting options, either use native failsafe position preset on the transmitter side,

or set failsafe on TFR8SB.

   2.2.1 Use native failsafe position preset on the transmitter side:

   If not disabling failsafe on the transmitter side, TFR8SB will use native failsafe position preset on the transmitter side.

   2.2.2 Set failsafe on TFR8SB side:

   TFR8SB supports failsafe function for all channels. Follow the steps below to set failsafe on TFR8SB:

     1) Bind the receiver first, and disable failsafe on the transmitter side;

     2) Set all transmitter controls to the desired failsafe position;

     3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is

set up successfully.

   I f you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.

   2.3LED status

RED LED

GREEN LED

Mode

Off

On

Normal mode

On

On

Waiting to be bound

Flashing

On

Signal lost

On

Flashing twice

Set failsafe

Flashing slowly

On

Normal speed mode

Flashing fast

On

High speed mode

3.  How to switch between two PPM modes

     Turn the transmitter off, connect the battery to the receiver, press the F/S button of receiver for 6 seconds and then release. The red LED will flash fast in HS Mode and slow in FS Mode. Repeat this to alternate modes.

Note: HS mode is only applied for high-speed digital servos. Other servos should select FS mode, otherwise servos will get hot or even burn out.

4.  Channel Setting Methods

      Channel setting for Futaba S.BUS servos and FrSky S Bus compatible servos can be performed at TFR8SB.

        1, Connect the SB port and RSSI port by the provided cable.

        2, Connect an S.BUS servo or S Bus compatible servo to the output connector (1~8) corresponding to the channel you want to set.

Output Connector

Channel Setting

Mode A

Mode B

1

1

9

2

2

10

3

3

11

4

4

12

5

5

13

6

6

14

7

7

15

8

8

16

        3, Connect battery to the receiver, RED blinking LED indicating the channel setting is completed in Mode A. To switch to Mode B, press the button on receiver for three seconds until GREEN LED starts to blink, indicating the channel setting is completed in Mode B.

          Mode A: RED LED blinks

          Mode B: GREEN LED blinks

Note: Do not perform linking procedure while motor’s main wire is connected or engine is operating, otherwise damage may occur. After linking is completed, recycle the receiver power and check if the receiver is really under control by linked transmitter.

Futaba is trade name and/or trademark of their respective companies and are not products of FrSky Electronic Co., Ltd.

 

Mer information

Vikt 0.0500 kg

Recensioner

Det finns inga produktrecensioner än.

Bli först med att recensera “FrSky TFR8SB 7-k FASST-mottagare Med PPM-utgång”